Tyco Network Card Escort5580TC User Manual

Introduction  
S
E
C
T
I
O
N
1
The Escort5580TC Voice Assisted Security Control provides easy to understand audible  
information about the status of your security system, and makes operation simple by  
prompting the user through each operation. In addition, you can use the Escort5580TC to  
control various Home Automation items. This new version of the Escort, designated ‘TC’ for  
Thermostat Control, now also allows you to monitor and control the temperature of your  
premises with the help of an EMS-100 thermostat.  
The Escort5580TC allows any touch-tone telephone to act as a keypad for your security  
system. The telephone could be any telephone that is on the same line as your security  
system, or an outside telephone which may be used to call the security system.  
Some optional features described in this manual may not be available on your security  
system. You will not hear the voice prompts for any option that is not activated on your  
system.  
In this manual, the voice messages are printed in bold and are enclosed in quotes, as  
shown here:  
“Enter your access code”  
Your installer may have programmed labels for the Escort to announce when it refers to  
things such as zones and partitions (e.g. you may hear "East wing" instead of "Partition 2").  
Prompts that your installer may have changed are written in brace brackets, as shown here:  
“To Select {Partition 2}, press [2].”  
When instructed to press a key or keys to perform an operation, symbols for the keys will be  
enclosed in square brackets, as shown here:  
Enter []  
1.1 About Your Security System  
Your DSC security equipment has been designed to give you the greatest possible  
flexibility and convenience. To fully benefit from the features of your security system, you  
should read this manual and the Instruction Manual provided with your system very  
carefully. Have your installer instruct you on system operation and on which features have  
been activated on your system. All users of the system should be instructed on its use. Fill  
out the System Information page in your Security System Instruction Manual and store it  
with the manual in a safe place for future reference.  
IMPORTANT NOTE: A security system cannot prevent emergencies. It is only intended  
to alert you and, if included, a central station of an emergency situation. Security  
systems are generally very reliable but they may not work under all conditions and  
they are not a substitute for prudent security practices or life and property insurance.  
Your security system should be installed and serviced by qualified security  
professionals who should instruct you on the level of protection that has been  
provided and on system operation.  
1
 
Accessing Your Security System  
S
E
C
T
I
O
N
2
With the Escort5580TC you can use a telephone (touch-tone only) to access your security  
system. This can be done either from a telephone on the premises (Local Access), or from a  
telephone off the premises anywhere in the world (Remote Access).  
2.1 Local Access  
Use this procedure to access your security system from a telephone that is on the same  
telephone line as your security system. No dial-in is necessary.  
Pick up the telephone; you will hear a dial tone.  
Enter your Telephone Access Code. The dial tone will stop and the system will announce:  
“Hello.”  
The system will then prompt:  
“Enter your access code.”  
Enter your [access code]. The system announces one or more messages to advise you of its  
status.  
2.2 Remote Access  
From any touch-tone telephone, first dial the number of your premises. If your premises  
have more than one line, be sure to call the number of the same line on which your  
Escort5580TC has been installed. After a single ring, hang up, wait 10 seconds, and call  
again. On the second call, the system will answer after one or two rings and announce:  
“Hello.”  
Now you must enter your Telephone Access Code within 10 seconds or the system will  
automatically hang up.  
The system will then prompt:  
“Enter your access code.”  
Enter your [access code] within 20 seconds or the system will hang up. The system will also  
hang up if 3 incorrect access codes are entered.  
Once an access code has been entered, the system will announce one or more messages to  
advise you of its status.  
NOTE: There is only one “Telephone Access Code”. It is programmed by your  
installer. It is not the same as your system access code, which you also enter on your  
system keypad. More than one system access code may be programmed for use by  
different users of your system (see section 8—Programming Access Codes).  
2.3 Receiving Incoming Calls  
If the Escort5580TC is being used on the premises at the same time as someone calls you,  
the system will announce:  
"Attention, you have an incoming call. To receive the call, press [#] now."  
To answer the incoming call, press [#]. To continue to use the Escort5580TC, don't press  
[#].  
3
 
A
C
C
E
S
S
I
N
G
Y
O
U
R
S
Y
S
T
E
M
2.4 What is a Partition?  
A partition is a group of zones which act independently of other groups of zones. Each  
partition acts as an independent alarm system. Partitions will have different access codes  
to arm and disarm them. The access codes assigned to one partition will not work on  
another partition. However, access codes can be assigned to more than one partition to  
allow someone to use one access code for several different partitions. Your installer will  
inform you how partitions and access codes have been assigned on your system.  
NOTE: If you have a two-partition system, be sure to have your installer explain if your  
Escort5580TC has been enabled to control one or both partitions.  
2.5 If You Have a Two-Partition System  
If you have a two-partition system, the Escort may prompt you to select a partition after  
entering your access code (as in Section 2—Accessing Your Security System). You will have  
to select a partition only if:  
· your Escort5580TC has been enabled to control both partitions  
· the access code you enter has been programmed to access both partitions  
If both of these are the case, the system will prompt you to select a partition as follows:  
“To Select {System}, press [1].”  
“To Select {Partition 2}, press [2].”  
(“{System}” in this case refers to Partition 1)  
Press [1] or [2], to select a partition.  
The system will announce the status of the selected partition.  
NOTE: Prompt words enclosed in brace brackets, “{ },” refer to labels. The system will  
announce the enclosed word by default unless it has been programmed to announce a  
specific label (e.g. you might hear “East Wing” instead of “{Partition 2}”).  
2.6 Fire, Auxiliary and Panic Alarms  
Your installer may have set up your system so that you can send a Fire, Auxiliary or Panic  
alarm at the press of a button. If so, using your telephone, you can:  
• send a Fire alarm by pressing and holding [1] on your telephone for 2 seconds  
• send an Auxiliary alarm by pressing and holding [2] on your telephone for 2 seconds  
• send a Panic alarm by pressing and holding [3] on your telephone for 2 seconds.  
Ask your installer for more information.  
NOTE: If the keypad lockout has been triggered by the entry of a number of incorrect  
access codes, the Fire, Auxiliary and Panic alarm buttons will not work.  
4
 
A
R
M
I
N
G
A
N
D
D
I
S
A
R
M
I
N
G
Arming and Disarming  
S
E
C
T
I
O
N
3
With the Escort5580TC, you can use a telephone to arm your system/partition (so that  
alarms, or other devices, will be activated when a zone on your premises is breached, such  
as when an Entry-Exit Door is opened). This can be done either locally or remotely.  
Similarly, you can use a telephone to disarm the system/partition.  
NOTE: DO NOT use a telephone with a redial button to arm or disarm your system.  
3.1 Away Arming  
NOTE: When arming your system/partition from a remote telephone, the system/  
partition will automatically be armed in Stay mode. (See section 3.2, below.)  
Access your system (Section 2—Accessing Your Security System) and select a partition  
(Section 2.5—If You Have a Two-Partition System).  
If the system/partition is ready to be armed, the system will prompt:  
“{System} is OFF.  
To turn ON, enter your access code.”  
Enter your [access code]. The system will then announce:  
“Turning {System} ON. Exit Delay in progress.  
To turn OFF, enter your access code.”  
If the system/partition is not ready to be armed, the system will prompt:  
“{System} is open. {Zone XX}  
Secure before turning ON.”  
When the “Secure before turning on” message is heard, ensure that any breached zones  
on the system/partition are secure (e.g. by closing any open doors that the system/partition  
monitors) before trying to arm the partition.  
NOTE: Depending on the model of control panel you have, you may be able to toggle  
Stay/Away zones on or off after your system has been armed. See your system's  
Instruction Manual for more information.  
3.2 At-Home Arming  
At-Home Arming allows you to arm the system/partition and remain on the premises. When a  
system is at-home armed, certain zones (Stay/Away zones) will not be armed, so that you can  
move freely in certain areas of the premises. Your installer should tell you which zones are  
Stay/Away zones. At-Home Arming also cancels the Entry Delay (see the Instruction Manual of  
your control panel) on the Entry-Exit Doors so that an alarm will sound immediately if the Entry-  
Exit Door is opened.  
When the system prompts:  
“{System} is OFF.  
To turn ON, enter your access code.”  
Activate the Stay Arming feature by pressing []. The system will then prompt:  
“To turn the system ON without Entry Delay, press [9],”  
Press [9]. The system will prompt:  
“Enter your access code.”  
5
 
A
R
M
I
N
G
A
N
D
D
I
S
A
R
M
I
N
G
Enter your [access code]. The system announces:  
“Turning {System} ON without Entry Delay. Exit Delay in progress”  
After exit delay expires, the selected partition will now be armed in At-Home Mode. Opening  
the entry-exit door will now sound an immediate alarm.  
NOTE: Depending on the model of control panel you have, you may be able to toggle  
Stay/Away zones on or off after your system has been armed. See your system's  
Instruction Manual for more information.  
3.3 Disarming  
IMPORTANT NOTE: If you return to the premises and find that an alarm has occurred  
while you were away, it is possible that an intruder may still be on the premises. Do  
not enter the premises. Go to the nearest telephone and contact the authorities.  
To disarm your system/partition, first access the system (Section 2—Accessing Your Security  
System) and select a partition (Section 2.5—If You Have a Two-Partition System).  
If the selected partition is armed, the system prompts:  
“{System} is on. To turn off, enter your access code.”  
Enter your [access code]. The system announces:  
“{System} is off.”  
If there were no alarms while the system/partition was armed, the system announces:  
“No alarms in memory.”  
If there were any alarms when the system/partition was armed, the system can announce  
how many there were and which zones were breached (see Section 3.5—Alarm Memory).  
When the system/partition is disarmed, additional messages may be announced to advise  
you of its status, or to allow you to select another partition.  
3.4 If An Alarm Sounds While You Are Home  
There are two possible types of alarm, a Fire Alarm and an Intrusion Alarm. Each can have its  
own distinctive tone. Your immediate response will depend on which has been sounded. You  
should have these responses planned ahead of time.  
Fire Alarm  
Your installer will inform you if fire detection equipment has been installed and activated on  
your system.  
Fire alarms will sound with a pulsing tone. If a fire alarm sounds, follow your emergency  
evacuation response plan immediately. Refer to the guidelines for Family Escape Planning  
(Section 8.2) at the back of this manual to construct your response plan.  
NOTE: Delay fire zones will not go into alarm while the Escort5580TC is being accessed.  
Intrusion Alarm  
Intrusion alarms will sound with either a continuous or pulsed tone (ask your installer). If an  
intrusion alarm sounds, an intruder may still be on the premises. Go to a safe place  
immediately. If you are certain that the premises are safe, you can silence the alarm by  
disarming the system.  
If the alarm was unintentional, notify your central station and/or the local authorities  
immediately to prevent an unnecessary response.  
You can determine the cause of an alarm by reviewing the alarm memory (see Section 3.5—  
Alarm Memory). Once the alarm has been cleared (i.e. zones secured) and the system  
disarmed, your system/partition can be re-armed.  
6
 
A
R
M
I
N
G
A
N
D
D
I
S
A
R
M
I
N
G
3.5 Alarm Memory  
Your system will record any alarms that occurred while the system/partition was armed. If an  
alarm occurred while the system/partition was armed, upon disarming it the following  
message will be announced:  
“There are (number) alarms in memory: {Zone XX}.”  
To hear again the zones that went into alarm, press []. The system will prompt:  
“For Alarm Memory, press [3].”  
Press [3], and the system will indicate the zones in Alarm Memory:  
“There are (number) alarms in memory, {Zone XX}.  
To exit, press [#].”  
When finished reviewing the zones in alarm memory, press [#] to return to the other system  
status messages.  
3.6 Bypassing Zones  
Zones may be bypassed when access is required to part of a protected area while the  
system/partition is armed. Once a system is armed, bypassed zones will not trigger an alarm  
when they are breached.  
You can only set a zone to be bypassed while the system is disarmed.  
To bypass zones, first access the security system (Section 2—Accessing Your Security  
System) and select a partition (Section 2.5—If You Have a Two-Partition System).  
The system will prompt:  
“{System} is OFF.  
To turn ON, enter your access code.  
For options, press [].”  
Press []. The system will announce the list of System Options. The system prompts:  
“For Zone Bypassing, press [1].”  
Press [1].  
If your system requires that you enter an access code to bypass zones, the system will  
prompt:  
“Enter your access code.”  
Enter your [access code].  
The system will announce the Zone Bypass menu:  
“There are (number) zones bypassed: {Zone XX}, etc...  
To exit, press [#].”  
To bypass a zone, enter the one- or two-digit zone number. The system will announce:  
“ There are (number) zones bypassed: {Zone XX}, etc..  
To exit, press [#].”  
You can now arm the system/partition at any time (see Section 3.1—Away Arming) and the  
zone(s) you selected will be bypassed. Zone bypasses are automatically removed each time  
the system/partition is disarmed and must be reapplied before the next arming. For security  
reasons, your installer may program your system to prevent the bypass function from  
affecting certain zones.  
7
 
S
E
C
T
I
O
N
7
Trouble Conditions  
S
E
C
T
I
O
N
4
The control panel continuously monitors a number of possible trouble conditions. If one or  
more of these conditions occur, the regular keypad will beep twice every ten seconds.  
There is no indication on a telephone until the system is accessed.  
To hear the trouble conditions present on your system/partition disarm the system  
(depending on the control panel you have, your system may allow you to enter the Trouble  
menu without first disarming the system/partition).  
Access the security system (Section 2—Accessing Your Security System) and select a  
partition (Section 2.5—If You Have a Two-Partition System).  
Press []. You will hear the prompt:  
“ For System Troubles, press [2].”  
Press [2] and the system will announce one or more of the trouble conditions from the list  
below, if any are present. If no trouble conditions are present, the system will announce:  
“ There are NO System Troubles.  
To exit, press [#].”  
The following describes the various trouble conditions that your system might announce:  
Announcement:  
Problem and how it should be addressed:  
“Service is required”  
If this message and no other trouble condition is announced, call for  
service.  
“AC Power Trouble.”  
“Phone line trouble.”  
“Communication trouble.”  
“ Zone Fault, press [5].”  
Electrical power to the system has been interrupted. Check your fuse  
box or circuit breaker to ensure that the electricity supply for the  
system is on. If this does not correct the problem, call for service.  
Your system has detected a problem with the telephone line. If this  
problem does not correct itself, or happens frequently, call for  
service.  
Your system has been unsuccessful in communicating an event to  
your central station. If you hear this message, call for service  
immediately.  
Your system has detected a Zone Fault on one or more zones. Press  
[5], and the system will announce which zones have a fault. If you  
are unsure of how to clear a zone fault, call for service.  
“Zone tamper, press [6].” Your system has detected a Zone Tamper on one or more zones.  
Press [6] and the system will announce which zone(s) have tampers.  
If you are unsure how to clear the zone tamper, call for service.  
“Device low battery,  
press [7].”  
Your system has detected that one or more of the wireless devices on  
the system has a low battery. Press [7], and the system will  
announce which devices have a low battery. Change the relevant  
batteries. If this does not correct the problem, call for service.  
“The time and date are  
incorrect.”  
If all power to the system is interrupted (AC and battery), the  
system clock and date will need to be reset. Press [], then [6],  
and the system will provide prompts for you to enter the time and  
date. If you are unsure of the cause of the system power failure,  
call for service.  
8
 
Setting Escort5580TC Options  
S
E
C
T
I
O
N
5
5.1 Setting The Time and Date  
With the system disarmed (Section 3.3—Disarming), access the security system (Section 2—  
Accessing Your Security System) and select a partition (Section 2.5—If You Have a Two-  
Partition System).  
Press []. You will hear the prompt:  
“ For Special Functions, press [6].”  
Press [6]. The system will prompt:  
“ Enter your Master Code.”  
Enter the Master Code. The system will prompt:  
“ For Time And Date, press [1].”  
Press [1]. The system announces the current time and date, and then prompts:  
“To change the time, press [1].  
To change the date, press [2].  
To exit, press [#].”  
You may either:  
· Press [1] to change the time. The system will prompt:  
“ Enter four digits for 24-hour time.”  
Enter the time in 24-hour clock format: 00 to 23 for the hour, and 00 to 59 for the minute.  
-or-  
· Press [2] to change the date. The system will prompt:  
“ Enter six digits for the month, day, and year.”  
Enter 01 to 12 for the month, 01 to 31 for the day, and 00 to 99 for the year.  
Upon programming information into either of these two sections the system will again  
announce the Time and Date menu.  
5.2 Volume Control  
The volume of the system messages/prompts can be controlled with this feature.  
With the system disarmed (Section 3.3—Disarming), access the security system (Section 2—  
Accessing Your Security System) and select a partition (Section 2.5—If You Have a Two-  
Partition System).  
Press []. You will hear the prompt:  
“ For Special Functions, press [6].”  
Press [6]. The system will prompt:  
“ Enter your Master Code”  
Enter the Master Code. The system will prompt:  
“ For Volume Control, press [2].”  
9
 
S
E
T
T
I
N
G
E
S
C
O
R
T
5
5
8
0
T
C
O
P
T
I
O
N
S
Press [2]. The system will then announce the current volume setting in one of three ways:  
“ Volume is low. To change volume, press [1].”  
“Volume is Medium. To change volume, press [1].”  
“ Volume is high. To change volume, press [1].”  
Press [1] to toggle through the volume levels until the desired volume is selected.  
Press [#] to return to the Special Functions menu.  
5.3 Speech Rate Control  
The speech rate of the system messages/prompts can be controlled with this feature.  
With the system disarmed (Section 3.3—Disarming), access the security system (Section 2—  
Accessing Your Security System) and select a partition (Section 2.5—If You Have a Two-  
Partition System).  
Press []. You will hear the prompt:  
“ For Special Functions, press [6]”  
Press [6]. The system will prompt:  
“ Enter your Master Code”  
Enter the Master Code. The system will prompt:  
“ For Speech Rate control, press [3]”  
Press [3]. The system will then announce the current speech rate in one of two ways:  
“Speech rate is fast. To change speech rate, press [1].”  
“Speech rate is slow. To change speech rate, press [1].”  
Press [1] to toggle between the speech rates until the desired rate is selected.  
Press [#] to return to the Special Functions Menu.  
5.4 Door Chime Feature  
When the Door Chime feature is enabled, a series of beeps will sound from the system’s  
keypads when certain specified zones are opened or closed. Your installer will inform you if  
the Door Chime feature is enabled, and which zones on the system will activate the chime.  
The Door Chime feature can be used to indicate the openings and closings of a door, such  
as a back door that is not always in sight.  
To enable the Door Chime feature you should first disarm your system (Section 3.3—  
Disarming; depending on the control panel you have, your system may allow you to enable  
the Door Chime feature without first disarming the partition). Access the security system  
(Section 2—Accessing Your Security System) and select a partition (Section 2.5—If You  
Have a Two-Partition System).  
Press []. You will hear the prompt:  
“ For Door Chime control, press [4].”  
Press [4]. You will hear one of the following:  
“Door Chime is ON/OFF”  
To turn the door chime on or off, press [4] again. To exit, press [#].  
10  
 
S
E
C
T
I
O
N
1
0
Home Automation  
S
E
C
T
I
O
N
6
The Home Automation feature allows you to control items (i.e. devices such as lights,  
appliances, etc.) with your security system. In addition, if one or more EMS-100 thermostats  
are installed, temperature can be controlled as well.  
Each item on your system may have been assigned to follow one or more preprogrammed  
schedules by your installer. For example, lights can be turned on and off at certain times of  
the day, and on certain days of the week. Scheduling can be used to give the premises the  
occupied appearance while you are away. Your installer should provide you with a list of  
which items have been programmed to follow which schedules, and the times that each  
schedule will follow. By knowing their schedules you will know when the various items on  
your system can be activated.  
In addition to items, you may have one or more thermostats on your system. The thermostats  
control the premises temperature according to temperature ranges called Occupancy  
Settings. Each thermostat can have up to four different Occupancy Settings, each of which  
can be assigned to follow one or more schedules. The schedules are programmed by your  
installer (see Section 6.6—Thermostat Control).  
To have schedules programmed or modified, contact your installer.  
6.1 How to Access the Home Automation Menu  
You can access the Home Automation menu when your system is either armed or disarmed.  
To use this menu, first access the security system (Section 2—Accessing Your Security  
System) and select a partition (Section 2.5—If You Have a Two-Partition System).  
Press []. The system will prompt:  
“For Automation Control and User Programming, press [5].”  
Press [5]. The system will prompt you with the Home Automation menu:  
“For Automation Control, press [1].  
For Temperature Control press [2]  
For User Programming, press [3].  
To exit, press [#].”  
11  
 
H
O
M
E
A
U
T
O
M
A
T
I
O
N
6.2 How to Use the Item Control Menu  
From the Home Automation menu, press [1]. The system may prompt you to enter your  
access code. The system will then prompt you with the Item Control menu. This menu allows  
you to choose individual items (devices which are controlled by Home Automation) and to  
turn them ON or OFF:  
Item Control Menu  
“{Item XX}.”  
Function  
Indicates the item or device selected.  
Turns ON the item.  
“To turn ON, press [1].”  
“To turn OFF, press [2].”  
Turns OFF the item.  
“For the next item, press [5].”  
“For the previous item, press [6].”  
“To select item using item number, press [7].”  
Advances to the next item.  
Skips back to the previous item.  
Lets you select another item by keying in its  
2-digit number.  
“To exit, press [#].”  
Returns to the Home Automation menu.  
Dimming  
The Dimming feature allows you to increase or decrease the brightness of an item, usually a light.  
NOTE: This feature will only be enabled on items capable of dimming.  
Items which have this feature enabled will have extra options in the Item Control menu. Only  
items with the Dimming feature enabled will have these options. If such an item is selected in  
the Item Control menu the system will announce the menu above with the addition of the  
following:  
Item Control Menu  
“To increase, press [3].”  
“To decrease, press [4].”  
Function  
Increases the brightness.  
Decreases the brightness.  
NOTE: The Escort5580TC allows [F], [A], and [P] alarms to be sent by holding down  
[1], [2], or [3], respectively, for two seconds. For this reason, do not hold down the [3]  
key to increase the brightness of an item. Press the [3] key in short intervals instead.  
6.3 Mode Control  
Modes give you control over groups of items and/or thermostat occupancy settings. When a  
mode is turned ON, each of the items/thermostat occupancy settings will automatically  
operate according to the schedule(s) assigned to them. For example, your installer may have  
programmed one of the modes as a {Vacation mode} that you can turn on to activate  
premises lights and thermostats while you are away.  
Your installer should provide you with a list of the items/occupancy settings that have been  
assigned to each mode (if any modes are used). Your system has a maximum of 8 modes  
available.  
NOTE: it is important to differentiate a “Mode” from a “Thermostat Mode” as defined in  
Section 6.6—Temperature Control.  
To operate items/thermostats according to modes, you must access the Mode Control menu.  
To do this, first access the Home Automation menu, then press [2]. The system will prompt  
you with the following:  
12  
 
H
O
M
E
A
U
T
O
M
A
T
I
O
N
Mode Control Menu  
Function  
“{Mode XX} is OFF/ON.”  
Indicates whether the current mode is ON or  
OFF.  
“To change, press [1].”  
Press [1] to toggle the mode ON or OFF.  
Press [2] to advance to the next mode.  
Press [3] to skip back to the previous mode.  
“For the next Mode, press [2].”  
“For the previous Mode, press [3].”  
“To exit, press [#].”  
Press [#] to return to the Home Automation  
menu.  
Use this menu to select any mode you want, and to turn it ON/OFF.  
6.4 Global Item Control  
Certain devices controlled by your system may be defined by your installer as Global Items.  
These items can be controlled together with a single command. For example, all of the lights  
on the premises may be all programmed as Global Items. You could then turn all the lights on  
or off at once. Your installer will inform you which automation items on your system are Global  
Items.  
From the Home Automation menu, select Global Item Control by pressing [3]. The system will  
prompt you with the following:  
“To turn Global Items ON, press [1].  
To turn Global Items OFF, press [2].  
To exit, press [#].”  
6.5 Output Control Feature  
The Output Control feature allows you to activate a programmable output on the main alarm  
control panel. This output can be used to temporarily open magnetically locked doors, or  
perform any function that requires a pulse of voltage to operate it. Up to 4 different output  
controls are available. Each can be programmed by your installer to activate a variety of  
devices. Ask your installer for more details.  
You may activate an Output Control while the system is armed or disarmed. Access the  
security system (Section 2—Accessing Your Security System) and select a partition (Section  
2.5—If You Have a Two-Partition System).  
Press []. You will hear the prompt:  
“ For {Output Control}, press [7].”  
Press [7]. You will hear the prompts:  
“For {Output Control 1}, press [1].”  
“For {Output Control 2}, press [2].”  
“For {Output Control 3}, press [3]."  
“For {Output Control 4}, press [4].”  
Press the key corresponding to the Output Control you want to activate.  
If an access code is required, you will hear the prompt:  
“Enter your access code”  
Enter your [access code]. The system will announce:  
13  
 
H
O
M
E
A
U
T
O
M
A
T
I
O
N
“{Output Control} in progress”  
The system will return to the main menu.  
6.6 Temperature Control  
Your installer may have connected one or more EMS-100 thermostats to your security  
system. This will give you control over your premises’ indoor temperature locally or remotely  
from any touch-tone telephone. The thermostat adjusts the temperature by controlling heating  
and/or cooling devices. By means of voice prompts your system can announce either indoor  
or outdoor temperatures (outdoor temperature, only if an outdoor sensor is attached).  
Each thermostat has four different Occupancy Settings: Day Setting, Night Setting, Auxiliary  
Setting, and Away Setting. For each Occupancy Setting, you can set a specific temperature  
range to be followed by the thermostat. Similar to items, each Occupancy Setting can be  
assigned by your installer to follow one or more schedules. Thus, you can program your  
thermostat to maintain different temperatures according to different schedules.  
You can also use your system to tell a thermostat to function in one of four Thermostat  
Modes: Off, Cool, Heat, or Automatic. If the thermostat has been connected by your installer  
to a cooling device (e.g. central air-conditioning system), you can select the Cool Mode to  
maintain temperature below a certain level with the cooling device. If the thermostat has been  
connected to a heating device (e.g. furnace system), you can select the Heat Mode to  
maintain temperature above a certain level with the heating device. If the thermostat has  
been connected to both a heating device and a cooling device, you may select the  
Automatic Mode to have your system use both devices to maintain temperature within a  
certain range.  
As with items, your installer can program an Occupancy Setting to operate when a mode is  
turned ON (see Section 6.3—Mode Control). Your installer can assign each Occupancy  
Setting to one or more Modes. For example, your installer may assign the Away Occupancy  
Setting to a {Vacation mode}, which you can turn on to maintain a particular temperature  
range when you are away.  
Temperature Control Menu  
To access Thermostat Controls, first access the Home Automation menu (press [][5]).  
Then press [2], to select Temperature Control. Enter your [access code] if you are prompted  
to do so. The system will now prompt you with the Temperature Control menu:  
“For Individual Thermostat Control, press [1].”  
“For Mode Control, press [2]”  
“To exit, press [#].”  
14  
 
H
O
M
E
A
U
T
O
M
A
T
I
O
N
Individual Thermostat Control Menu  
To change settings on any thermostat, press [1]. The system will prompt you with the  
Individual Thermostat Control menu:  
Individual Thermostat Control Menu  
Function  
“{Thermostat XX}.”  
Indicates the thermostat selected.  
“Interior temperature is (XX) degrees.”  
“Exterior temperature is (XX) degrees.”  
“The Occupancy Setting is  
Indicates the interior temperature.  
Indicates the exterior temperature.  
Indicates which Occupancy Setting is active.  
(Auxiliary/Day/Away/Night).”  
“The Thermostat Mode is  
Indicates which Thermostat Mode is active.  
(Off/Cool/Heat/Automatic)”  
“The Fan is (On/Automatic).”  
Indicates the state of the fan. (On = continuous  
fan; Automatic = fan comes on when heating/  
cooling device is on)  
“To set temperature, press [1].”  
“For Occupancy Setting, press [2].”  
Accesses the Temperature Setting menu.  
Accesses the Occupancy Mode Selection  
menu.  
“For Thermostat Mode, press [3].”  
Accesses the Thermostat Mode Selection  
menu.  
“For Fan Control, press [4].”  
“For the next thermostat, press [5].”  
“For the previous thermostat, press [6].”  
“To select thermostat using thermostat  
number, press [7].”  
Accesses the Fan Control menu.  
Advances to the next thermostat.  
Skips back to the previous thermostat.  
Lets you select another thermostat by  
keying in its 2-digit number.  
“To exit, press [#].”  
Returns to the Temperature Control menu.  
NOTE: Some prompts may not be announced depending how your system is  
programmed.  
To set the temperature range for the current Occupancy Setting, press [1]. The system prompts:  
“Cool temperature is (XX) degrees.  
Heat temperature is (XX) degrees.  
To change Cool temperature, press [1].  
To change Heat temperature, press [2].  
To exit, press [#].”  
To switch the thermostat to a different Occupancy Setting, press [2]. The system prompts:  
“The Occupancy Mode is Auxiliary/Day/Away/Night.  
To change, press [1].  
To exit, press [#].”  
15  
 
H
O
M
E
A
U
T
O
M
A
T
I
O
N
To switch the thermostat to a different Thermostat Mode, press [3]. The system prompts:  
“The Thermostat Mode is Off/Cool/Heat/Automatic.  
To change, press [1].  
To exit, press [#].”  
To change the fan setting, press [4]. The system prompts:  
“The fan is On/Automatic.  
To change, press [1].  
To exit, press [#].”  
6.7 Accessing Temperature Control from an LCD5500Z Keypad  
If you have an LCD5500Z keypad on your system, you can access the temperature control  
menu from there:  
1. Press []  
2. Use the <> buttons to scroll to the "Thermostat Ctrl" menu.  
3. Press [].  
4.Use the <> buttons to scroll to the thermostat whose settings you want to change. When  
the desired thermostat is displayed, press [].  
5. You can now select any of five options:  
• Set Temperature  
• Occupancy Setting  
• Thermostat Mode  
• Fan Control  
• Keypad View  
The first four options allow you to change the settings on the currently selected  
thermostat, in a similar manner to the Escort5580TC menus described in section 6.6.  
Use the Keypad View option to determine which thermostat's indoor/outdoor temperature  
to display on the keypad. The keypad will display the temperature when it is not in use.  
Each keypad can be programmed to display the temperature of a different thermostat.  
6.To exit the Thermostat Control menu, press [#].  
6.8 Video Camera Triggering  
The Escort5580TC can be used to remotely control the triggering of video cameras. This  
can only be done with security systems that have cameras connected to them via a  
PC5108L module (ask your installer for more details). The Video Camera Triggering feature  
will cause cameras to take pictures according to a sequence (or script) that has been  
programmed in the PC5108L module.  
To access this feature, access your system remotely (Section 2.2—Remote Access).  
Press [], then [8]. Your system will prompt:  
"Enter your access code."  
Enter your [access code]. The system will announce:  
"Goodbye."  
The system will then hang up so that the PC5108L can run the programmed script.  
16  
 
Programming Access Codes  
S
E
C
T
I
O
N
7
The Access Code Programming feature allows you to program access codes (the Master  
Code may not be changeable with this feature) that will function on the security system as  
well as on the Escort. Your system will either have 4- or 6-digit access codes. Depending  
on what model of security system you have, you may have the option to program up to 37 of  
these codes.  
Access codes are programmed as follows:  
While disarmed, access your security system (Section 2—Accessing Your Security System)  
and select a partition (Section 2.5—If You Have a Two-Partition System).  
Press []. The system will prompt:  
“For Automation Control and User Programming, press [5].”  
Press [5]. The system will then prompt:  
“For Automation Control, press [1].  
For Temperature Control, press [2].  
For User Programming, press [3].  
To exit, press [#].”  
Press [3]. Enter the [master code]. The system will then prompt:  
“User Code Programming.  
Enter the one-/two-digit User Number.  
For User Option Programming, press [9].  
Users X, Y and Z are programmed.  
To exit, press [#].”  
NOTE: Your system may or may not prompt you with the User Option Programming  
prompt. Please consult your security system’s User’s Manual for more information on  
User Options.  
Enter the number that specifies which access code you want to program. The system will  
announce:  
“Enter the new 4-/6-digit access code.  
To exit, press [#].”  
Enter the new code. You will again be prompted:  
“User Code Programming.  
Enter the one-/two-digit User Number.  
For User Option Programming, press [9].  
Users X, Y and Z are programmed.  
To exit, press [#].”  
If you wish to program another access code, enter the user number. If not, press [#] to return  
to the main menu.  
17  
 
S
E
C
T
I
O
N
1
3
Fire and Safety in the Home  
S
E
C
T
I
O
N
8
Most fires occur in the home, and to minimize this danger it is recommended that a  
household fire safety audit be conducted and a family escape plan be developed.  
8.1 Household Fire Safety  
Check your home for the following potential hazards:  
• Are all electrical appliances and outlets in a safe condition? Check for frayed cords,  
overloaded lighting circuits, and so on. If you are uncertain about the condition of your  
electrical appliances or household electrical service, have a professional evaluation.  
• Are all flammable liquids stored safely in closed containers in a well-ventilated and cool area?  
Cleaning with flammable liquids, such as gasoline, should be avoided. Refer to product  
instructions, printed warnings and labels for information on using and storing hazardous  
materials safely.  
• Are fire hazardous materials (such as matches) well out of the reach of children?  
• Are furnaces and wood burning appliances properly installed, clean, and in good working  
order? If in doubt, have a professional evaluation.  
8.2 Family Escape Planning  
There is often very little time between the detection of a fire and the time at which it becomes  
deadly. Because of this, it is very important that a family escape plan be developed, practiced  
and followed.  
1.Every family member should participate in developing the escape plan.  
2.Study the possible escape routes from each location within the house. Since many fires occur  
at night, special attention should be given to the escape routes from sleeping quarters.  
3.It is essential that escape from a bedroom be possible without opening the interior door.  
Consider the following when making your escape plans:  
• Make sure that doors and windows that open to the outside are easily opened. Ensure that  
they are not painted shut and that their locking mechanisms operate smoothly.  
• If opening an exit or using an exit is too difficult for children, the elderly or handicapped, plans  
for rescue should be developed. This includes making sure that those who are to perform the  
rescue can promptly hear the fire warning signal.  
• If the exit is above ground level, an approved fire ladder or rope should be provided, as well  
as training in its use.  
• Exits on the ground level should be kept clear. Be sure to remove snow from exterior patio  
doors in winter. Outdoor furniture or equipment should not block exits.  
• The family should have a predetermined assembly point where everyone can be accounted  
for; for example, across the street or at a neighbour’s house.  
• Once everyone is out of the house, call the Fire Department.  
• A good plan emphasizes quick escape. Do not investigate first or attempt to fight the fire, and  
do not attempt to rescue belongings as this takes up valuable time. Once outside, do not re-  
enter the house. Wait for the fire department.  
• Write the plan down and rehearse frequently, so that should an emergency arise, everybody  
will know what they are to do. Revise the plan as conditions change; for example, when there  
are more or fewer family members in the home, or if there are physical changes to the house.  
• Make sure your fire warning system is operational by conducting weekly tests. If you are  
unsure about system operation, contact your installing company.  
• It is recommended that you contact your local fire department and request further information  
on home fire safety and escape planning. If available, have your local fire prevention officer  
conduct an in-house fire safety inspection.  
18  
 
Glossary  
S
E
C
T
I
O
N
9
Access Code .................... A 4- or 6-digit code that allows users to access arming, disarming  
and other system functions. Different access codes may be  
assigned to different users.  
Item.................................... Items are devices (e.g. lights, appliances, etc.) that can be  
controlled within the Home Automation feature of the Escort system.  
Such devices can be controlled using a touch-tone telephone.  
Mode.................................. Modes give you control over groups of items or thermostat  
occupancy settings programmed for scheduled or event initiated  
operation. When a mode is turned ON, each of the items/thermostat  
occupancy settings will automatically operate according to the  
schedule(s) or panel events assigned to them.  
Example: your installer may have programmed a "Vacation" mode  
that you can turn on to activate premises lights and thermostats while  
you are away.  
Occupancy Setting ...........Each thermostat has four different temperature ranges that can be  
programmed. These temperature ranges are called Occupancy  
Settings:  
Day Occupancy Setting  
Night Occupancy Setting  
Auxiliary Occupancy Setting  
Away Occupancy Setting.  
These occupancy settings allow you to easily change the  
temperature range for the area controlled by the thermostat.  
Depending on which Thermostat Mode is turned on, the thermostat  
will use either heating or cooling devices to maintain the  
temperature within the range programmed for the occupancy  
setting.  
Output Control ................. A control which allows you to activate an output on the main alarm  
control panel. This output can be programmed by the installer to  
activate a variety of devices (e.g. to temporarily open magnetically  
locked doors).  
Partition ............................ A group of zones on the system which are armed/disarmed and  
controlled independently of other zones grouped into a separate  
partition. Each partition has its own keypad and can be assigned its  
own access codes.  
Telephone Access Code . A 3-digit security code that must be entered when using a telephone  
to access the Escort system. The code must be entered whether  
calling locally (from a telephone on the premises and on the same  
line as the Escort) or remotely (from any other touch-tone  
telephone). Once access is gained to the Escort, a normal system  
access code is still usually required to access system functions.  
Thermostat Mode............. One of the four modes in which an EMS-100 thermostat can be  
operating: Off, Heat, Cool, Automatic.  
Zone .................................. An area (e.g. a room) or barrier (e.g. a door) within the premises that  
is monitored by a detector (e.g. smoke detector, door/window  
contact, motion detector, glassbreak detector, etc.).  
19  
 
product under this warranty after a reasonable number of attempts  
will be limited to a replacement of the product, as the exclusive  
remedy for breach of warranty. Under no circumstances shall Digi-  
tal Security Controls Ltd. be liable for any special, incidental, or  
consequential damages based upon breach of warranty, breach of  
contract, negligence, strict liability, or any other legal theory. Such  
damages include, but are not limited to, loss of profits, loss of the  
product or any associated equipment, cost of capital, cost of sub-  
stitute or replacement equipment, facilities or services, down time,  
purchasers time, the claims of third parties, including customers,  
and injury to property.  
LIMITED WARRANTY  
Digital Security Controls Ltd. warrants the original purchaser that  
for a period of twelve months from the date of purchase, the prod-  
uct shall be free of defects in materials and workmanship under  
normal use. During the warranty period, Digital Security Controls  
Ltd. shall, at its option, repair or replace any defective product  
upon return of the product to its factory, at no charge for labour  
and materials. Any replacement and/or repaired parts are warranted  
for the remainder of the original warranty or ninety (90) days,  
whichever is longer. The original owner must promptly notify Digi-  
tal Security Controls Ltd. in writing that there is defect in material  
or workmanship, such written notice to be received in all events  
prior to expiration of the warranty period.  
Disclaimer of Warranties  
This warranty contains the entire warranty and shall be in lieu  
of any and all other warranties, whether expressed or implied  
(including all implied warranties of merchantability or fitness  
for a particular purpose) And of all other obligations or liabili-  
ties on the part of Digital Security Controls Ltd. Digital Security  
Controls Ltd. neither assumes nor authorizes any other person  
purporting to act on its behalf to modify or to change this war-  
ranty, nor to assume for it any other warranty or liability con-  
cerning this product.  
International Warranty  
The warranty for international customers is the same as for any  
customer within Canada and the United States, with the excep-  
tion that Digital Security Controls Ltd. shall not be responsible  
for any customs fees, taxes, or VAT that may be due.  
Warranty Procedure  
To obtain service under this warranty, please return the item(s) in  
question to the point of purchase. All authorized distributors and  
dealers have a warranty program. Anyone returning goods to Digital  
Security Controls Ltd. must first obtain an authorization number.  
Digital Security Controls Ltd. will not accept any shipment what-  
soever for which prior authorization has not been obtained.  
This disclaimer of warranties and limited warranty are gov-  
erned by the laws of the province of Ontario, Canada.  
WARNING: Digital Security Controls Ltd. recommends that the  
entire system be completely tested on a regular basis. However,  
despite frequent testing, and due to, but not limited to, criminal  
tampering or electrical disruption, it is possible for this product  
to fail to perform as expected.  
Conditions to Void Warranty  
This warranty applies only to defects in parts and workmanship  
relating to normal use. It does not cover:  
Installer’s Lockout  
Any products returned to DSC which have the Installers Lock-  
out option enabled and exhibit no other problems will be sub-  
ject to a service charge.  
• damage incurred in shipping or handling;  
• damage caused by disaster such as fire, flood, wind, earthquake  
or lightning;  
• damage due to causes beyond the control of Digital Security Con-  
trols Ltd. such as excessive voltage, mechanical shock or water  
damage;  
• damage caused by unauthorized attachment, alterations, modi-  
fications or foreign objects;  
Out of Warranty Repairs  
Digital Security Controls Ltd. will at its option repair or replace  
out-of-warranty products which are returned to its factory accord-  
ing to the following conditions. Anyone returning goods to Digital  
Security Controls Ltd. must first obtain an authorization number.  
Digital Security Controls Ltd. will not accept any shipment what-  
soever for which prior authorization has not been obtained.  
• damage caused by peripherals (unless such peripherals were sup-  
plied by Digital Security Controls Ltd.);  
• defects caused by failure to provide a suitable installation envi-  
ronment for the products;  
• damage caused by use of the products for purposes other than  
those for which it was designed;  
Products which Digital Security Controls Ltd. determines to be  
repairable will be repaired and returned. A set fee which Digital  
Security Controls Ltd. has predetermined and which may be re-  
vised from time to time, will be charged for each unit repaired.  
• damage from improper maintenance;  
• damage arising out of any other abuse, mishandling or improper  
application of the products.  
Products which Digital Security Controls Ltd. determines not to  
be repairable will be replaced by the nearest equivalent product  
available at that time. The current market price of the replace-  
ment product will be charged for each replacement unit.  
Digital Security Controls Ltd.s liability for failure to repair the  
© 1998 Digital Security Controls Ltd.  
Printed in Canada 29003015 R0  
 
• W A R N I N G •  
This manual contains information on limitations regarding product use and function  
and information on the limitations as to liability of the manufacturer.  
Instruction  
Manual  
ESCORT558OTC  
Version 2.0  
 
equivalent, in such a manner as to allow for easy, immediate disconnection of  
the terminal equipment. Standard jacks shall be so arranged that, if the plug  
connected there is withdrawn, no interference to the operation of the  
equipment at the customer’spremises whichremainsconnectedtothetelephone  
network shall occur by reason of such withdrawal.  
FCC COMPLIANCE STATEMENT  
CAUTION:ChangesormodificationsnotexpresslyapprovedbyDigitalSecurity  
Controls Ltd. could void your authority to use this equipment.  
This equipment generates and uses radio frequency energy and if not installed  
and used properly, in strict accordance with the manufacturer’s instructions,  
may cause interference to radio and television reception. It has been type  
tested and found to comply with the limits for Class B device in accordance  
with the specifications in Subpart “B” of Part 15 of FCC Rules, which are  
designed to provide reasonable protection against such interference in any  
residential installation. However, there is no guarantee that interference will  
not occur in a particular installation. If this equipment does cause interference  
to television or radio reception, which can be determined by turning the  
equipment off and on, the user is encouraged to try to correct the interference  
by one or more of the following measures:  
INCIDENCE OF HARM Should terminal equipment or protective circuitry  
cause harm to the telephone network, the telephone company shall, where  
practicable, notify the customer that temporary disconnection of service may  
be required; however, where prior notice is not practicable, the telephone  
company may temporary discontinue service if such action is deemed  
reasonable in the circumstances. In the case of such temporary  
discontinuance, the telephone company shall promptly notify the customer  
and will be given the opportunity to correct the situation. The customer also  
has the right to bring a complaint to the FCC if he feels the disconnection is  
not warranted.  
Re-orient the receiving antenna  
CHANGE IN TELEPHONE COMPANY EQUIPMENT OR FACILITIES  
The Telephone Company may make changes in its communicationsfacilities,  
equipment,operationsorprocedures, where such actions is reasonably required  
and proper in its business. Should any such changes render the customer’s  
terminal equipment incompatible with the telephone company facilities the  
customer shall be given adequate notice to the effect of the modifications to  
maintain uninterrupted service.  
Relocate the alarm control with respect to the receiver  
Move the alarm control away from the receiver  
Connect the alarm control into a different outlet so that alarm control  
and receiver are on different circuits.  
If necessary, the user should consult the dealer or an experienced radio/  
television technician for additional suggestions. The user may find the  
following booklet prepared by the FCC helpful: ”How to Identify and  
Resolve Radio/Television Interference Problems.” This booklet is  
available from the U.S. Government Printing Office, Washington, D.C.  
20402, Stock # 004-000-00345-4.  
GENERAL This equipment should not be used on coin telephone lines.  
Connection to party line service is subject to state tariffs.  
RINGER EQUIVALENCE NUMBER (REN) The REN is useful to determine  
the quantity of devices that you may connect to your telephone line and still  
have all of those devices ring when your telephone number is called. In most,  
but not all areas, the sum of the REN’s of all devices connected to one line  
should not exceed five (5). To be certain of the number of devices that you may  
connect to your line, you may want to contact your local telephone company.  
IMPORTANT INFORMATION  
FCC Registration Number: F53CAN-22830-KX-N, Ringer Equivalence  
Number: 0.2B, USOC Jack: RJ-31X  
MALFUNCTION OF THE EQUIPMENT In the event that this equipment  
should fail to operate properly, the customer shall disconnect the equipment from  
the telephone line to determine if it is the customer’s equipment which is not  
working properly, or if the problem is with the telephone company network. If the  
problem is with this equipment, the customer shall discontinue use until it is  
repaired.  
EQUIPMENT MAINTENANCE FACILITY  
Digital Security Controls Ltd. 160 Washburn St.Lockport, NY 14094  
TELEPHONE CONNECTION REQUIREMENTS Except for the telephone  
company provided ringers, all connections to the telephone network shall be  
made through standard plugs and telephone company provided jacks, or  
AVIS: L’étiquette de l’Industrie Canada identifie le matériel homologué. Cette  
étiquette certifie que le matériel est conforme à certaines normes de protection,  
d’exploitation et de sécurité des réseaux de télécommunications. Industrie Canada  
n’assure toutefois pas que le matériel fonctionnera à la satisfaction de l’utilisateur.  
NOTICE: The Industry Canada label identifies certified equipment. This  
certification means that the equipment meets certain telecommunications network  
protective, operational and safety requirements. Industry Canada does not guarantee  
the equipment will operate to the user’s satisfaction.  
Avant d’installer ce matériel, l’utilisateur doit s’assurer qu’il est permis de le  
raccorder aux installations de l’entreprise locale de télécommunication. Le matériel  
doit également être installé en suivant une méthode acceptée de raccordement.  
L’abonné ne doit pas oublier qu’il est possible que la conformité aux conditions  
énoncées ci-dessus n’empêchent pas la dégradation du service dans certaines  
situations.  
Les réparations de matériel homologué doivent être effectuées par un centre  
d’entretien canadien autorisé désigné par le fournisseur. La compagnie de  
télécommunications peut demander à l’utilisateur de débrancher un appareil à la  
suite de réparations ou de modifications effectuées par l’utilisateur ou à cause de  
mauvais fonctionnement.  
Pour sa propre protection, l’utilisateur doit s’assurer que tous les fils de mise à la  
terre de la source d’énergie électrique, les lignes téléphoniques et les canalisations  
d’eau métalliques, s’il y en a, sont raccordés ensemble. Cette précaution est  
particulièrement importante dans les régions rurales.  
AVERTISSEMENT: L’utilisateur ne doit pas tenter de faire ces raccordements  
lui-même; il doit avoir recours à un service d’inspection des installations électriques,  
ou à un électricien, selon le cas.  
Before installing this equipment, users should ensure that it is permissible to be  
connected to the facilities of the local telecommunications company. The equipment  
must also be installed using an acceptable method of connection. The customer  
should be aware that compliance with the above conditions may not prevent  
degradation of service in some situations.  
Repairs to certified equipment should be made by an authorized Canadian  
maintenance facility designated by the supplier. Any repairs or alterations made by  
the user to this equipment, or equipment malfunctions, may give the  
telecommunications company cause to request the user to disconnect the equipment.  
User should ensure for their own protection that the electrical ground connections  
of the power utility, telephone lines and internal metallic water pipe system, if  
present, are connected together. This precaution may be particularly important in  
rural areas.  
CAUTION: Users should not attempt to make such connections themselves, but  
should contact the appropriate electric inspection authority, or electrician, as  
appropriate.  
The Load Number (LN) assigned to each terminal device denotes the percentage  
of the total load to be connected to a telephone loop which is used by the device, to  
prevent overloading. The termination on a loop may consist of any combination of  
devices subject only to the requirement that the total of the Load Numbers of all  
the devices does not exceed 100.  
L’indice de charge (IC) assigné a chaque dispositif terminal indique, pour éviter  
toute surcharge, le pourcentage de la charge totale qui peut être raccordée à un  
circuit téléphonique bouclé utilisé par ce dispositif. La terminaison du circuit bouclé  
peut être constituée de n’importe quelle combinaison de dispositifs, pourvu que la  
somme des indices de charge de l’ensemble des dispositifs ne dépasse pas 100.  
LIndice de charge de ce produit est 2.  
The Load Number of this unit is 2.  
 
Table of Contents  
1: Introduction ..................................................................................................................................... 1  
1.1  
1.2  
1.3  
1.4  
About Your Security System ................................................................................................ 1  
General System Operation .................................................................................................. 2  
Access Codes ..................................................................................................................... 2  
Audio Help ........................................................................................................................... 2  
2: Accessing Your Security System .................................................................................................. 3  
2.1  
2.2  
2.3  
2.4  
2.5  
2.6  
Local Access ....................................................................................................................... 3  
Remote Access.................................................................................................................... 3  
Receiving Incoming Calls .................................................................................................... 3  
What is a Partition? .............................................................................................................. 4  
If You Have a Two-Partition System ..................................................................................... 4  
Fire, Auxiliary and Panic Alarms.......................................................................................... 4  
3: Arming and Disarming ................................................................................................................... 5  
3.1  
3.2  
3.3  
3.4  
3.5  
3.6  
Away Arming........................................................................................................................ 5  
At-home Arming ................................................................................................................... 5  
Disarming............................................................................................................................. 6  
If An Alarm Sounds While You Are Home ............................................................................ 6  
Alarm Memory...................................................................................................................... 7  
Bypassing Zones ................................................................................................................. 7  
4:Trouble Conditions .......................................................................................................................... 8  
5: Setting Escort5580TC Options ...................................................................................................... 9  
5.1  
5.2  
5.3  
5.4  
Setting The Time and Date .................................................................................................. 9  
Volume Control..................................................................................................................... 9  
Speech Rate Control.......................................................................................................... 10  
Door Chime Feature........................................................................................................... 10  
6: Home Automation ......................................................................................................................... 11  
6.1  
6.2  
6.3  
6.4  
6.5  
6.6  
6.7  
6.8  
How to Access the Home Automation Menu .................................................................... 11  
How to Use the Item Control Menu .................................................................................... 12  
Mode Control ..................................................................................................................... 12  
Global Item Control ............................................................................................................ 13  
Output Control Feature ...................................................................................................... 13  
Temperature Control .......................................................................................................... 14  
Accessing Temperature Control from an LCD5500Z Keypad ........................................... 16  
Video Camera Triggering................................................................................................... 16  
7: Programming Access Codes ....................................................................................................... 17  
8: Fire and Safety in the Home ........................................................................................................ 18  
8.1  
8.2  
Household Fire Safety ....................................................................................................... 18  
Family Escape Planning .................................................................................................... 18  
9: Glossary......................................................................................................................................... 19  
i
 
another level of the residence or building.  
WARNING Please Read Carefully  
Every fire is different in the amount of smoke produced and the rate of  
burning. Smoke detectors cannot sense all types of fires equally well.  
Smoke detectors may not provide timely warning of fires caused by care-  
lessness or safety hazards such as smoking in bed, violent explosions,  
escaping gas, improper storage of flammable materials, overloaded elec-  
trical circuits, children playing with matches or arson.  
System Failures  
This system has been carefully designed to be as effective as possible. There  
are circumstances, however, involving fire, burglary, or other types of emer-  
gencies where it may not provide protection. Any alarm system of any type  
may be compromised deliberately or may fail to operate as expected for a  
variety of reasons. Some but not all of these reasons may be:  
Even if the smoke detector operates as intended, there may be circumstances  
when there is insufficient warning to allow all occupants to escape in time to  
avoid injury or death.  
Inadequate Installation  
A security system must be installed properly in order to provide adequate  
protection. Every installation should be evaluated by a security professional  
to ensure that all access points and areas are covered. Locks and latches on  
windows and doors must be secure and operate as intended. Windows, doors,  
walls, ceilings and other building materials must be of sufficient strength and  
construction to provide the level of protection expected. A reevaluation must  
be done during and after any construction activity. An evaluation by the fire  
and/or police department is highly recommended if this service is available.  
Motion Detectors  
Motion detectors can only detect motion within the designated areas as  
shown in their respective installation instructions. They cannot discrimi-  
nate between intruders and intended occupants. Motion detectors do  
not provide volumetric area protection. They have multiple beams of  
detection and motion can only be detected in unobstructed areas cov-  
ered by these beams. They cannot detect motion which occurs behind  
walls, ceilings, floor, closed doors, glass partitions, glass doors or win-  
dows. Any type of tampering whether intentional or unintentional such  
as masking, painting, or spraying of any material on the lenses, mir-  
rors, windows or any other part of the detection system will impair its  
proper operation.  
Criminal Knowledge  
This system contains security features which were known to be effective at  
the time of manufacture. It is possible for persons with criminal intent to  
develop techniques which reduce the effectiveness of these features. It is im-  
portant that a security system be reviewed periodically to ensure that its fea-  
tures remain effective and that it be updated or replaced if it is found that it  
does not provide the protection expected.  
Passive infrared motion detectors operate by sensing changes in tempera-  
ture. However their effectiveness can be reduced when the ambient tem-  
perature rises near or above body temperature or if there are intentional  
or unintentional sources of heat in or near the detection area. Some of  
these heat sources could be heaters, radiators, stoves, barbeques, fire-  
places, sunlight, steam vents, lighting and so on.  
Access by Intruders  
Intruders may enter through an unprotected access point, circumvent a  
sensing device, evade detection by moving through an area of insuffi-  
cient coverage, disconnect a warning device, or interfere with or prevent  
the proper operation of the system.  
Warning Devices  
Warning devices such as sirens, bells, horns, or strobes may not warn  
people or waken someone sleeping if there is an intervening wall or  
door. If warning devices are located on a different level of the residence  
or premise, then it is less likely that the occupants will be alerted or  
awakened. Audible warning devices may be interfered with by other  
noise sources such as stereos, radios, televisions, air conditioners or  
other appliances, or passing traffic. Audible warning devices, however  
loud, may not be heard by a hearing-impaired person.  
Power Failure  
Control units, intrusion detectors, smoke detectors and many other security  
devices require an adequate power supply for proper operation. If a device  
operates from batteries, it is possible for the batteries to fail. Even if the bat-  
teries have not failed, they must be charged, in good condition and installed  
correctly. If a device operates only by AC power, any interruption, however  
brief, will render that device inoperative while it does not have power. Power  
interruptions of any length are often accompanied by voltage fluctuations which  
may damage electronic equipment such as a security system. After a power  
interruption has occurred, immediately conduct a complete system test to en-  
sure that the system operates as intended.  
Telephone Lines  
If telephone lines are used to transmit alarms, they may be out of service or  
busy for certain periods of time. Also an intruder may cut the telephone line or  
defeat its operation by more sophisticated means which may be difficult to  
detect.  
Failure of Replaceable Batteries  
This systems wireless transmitters have been designed to provide several years  
of battery life under normal conditions. The expected battery life is a function  
of the device environment, usage and type. Ambient conditions such as high  
humidity, high or low temperatures, or large temperature fluctuations may  
reduce the expected battery life. While each transmitting device has a low  
battery monitor which identifies when the batteries need to be replaced, this  
monitor may fail to operate as expected. Regular testing and maintenance will  
keep the system in good operating condition.  
Insufficient Time  
There may be circumstances when the system will operate as intended, yet  
the occupants will not be protected from the emergency due to their inabil-  
ity to respond to the warnings in a timely manner. If the system is moni-  
tored, the response may not occur in time to protect the occupants or their  
belongings.  
Component Failure  
Although every effort has been made to make this system as reliable as pos-  
sible, the system may fail to function as intended due to the failure of a compo-  
nent.  
Compromise of Radio Frequency (Wireless) Devices  
Signals may not reach the receiver under all circumstances which could  
include metal objects placed on or near the radio path or deliberate jam-  
ming or other inadvertent radio signal interference.  
Inadequate Testing  
Most problems that would prevent an alarm system from operating as  
intended can be found by regular testing and maintenance. The complete  
system should be tested weekly and immediately after a break-in, an at-  
tempted break-in, a fire, a storm, an earthquake, an accident, or any kind  
of construction activity inside or outside the premises. The testing should  
include all sensing devices, keypads, consoles, alarm indicating devices  
and any other operational devices that are part of the system.  
System Users  
A user may not be able to operate a panic or emergency switch possibly due to  
permanent or temporary physical disability, inability to reach the device in  
time, or unfamiliarity with the correct operation. It is important that all sys-  
tem users be trained in the correct operation of the alarm system and that they  
know how to respond when the system indicates an alarm.  
Smoke Detectors  
Security and Insurance  
Smoke detectors that are a part of this system may not properly alert occupants of  
a fire for a number of reasons, some of which follow. The smoke detectors may  
have been improperly installed or positioned. Smoke may not be able to reach the  
smoke detectors, such as when the fire is in a chimney, walls or roofs, or on the  
other side of closed doors. Smoke detectors may not detect smoke from fires on  
Regardless of its capabilities, an alarm system is not a substitute for  
property or life insurance. An alarm system also is not a substitute for  
property owners, renters, or other occupants to act prudently to prevent  
or minimize the harmful effects of an emergency situation.  
ii  
 

Targus Mouse Wireless Multimedia Presenter with Trackball User Manual
Taylor Blender AB 1051 BL User Manual
Tech Craft TV Video Accessories SHK4836E User Manual
Texas Instruments Marine Instruments bq27500 User Manual
Thermo Products Furnace OH5 85DXE User Manual
Toastmaster Electric Steamer TMFS4401 User Manual
Toshiba Laptop A4 User Manual
UltraViolet Devices Air Cleaner Air Disinfection User Manual
Universal Remote Control Universal Remote UR5U BH8000 User Manual
Victor Technology Calculator 1228 2 User Manual